Analysis of the penetration of NaOCl 5.25% into dentinal tubules using different irrigation protocols: An ex vivo study.

The objective of the study was to investigate the 5.25% sodium hypochlorite (NaOCl) penetration into the dentinal tubules after different irrigation methods. Seventy canines were stained with 1% crystal violet and divided into groups (n = 20): GEC-EasyClean; GPUI-E1 Irrisonic ultrasonic insert; GXP-XP-Endo finisher; GPC-conventional irrigation and GNC-stained tooth without irrigation. Axial sections (16×) were assessed and irrigant penetration was quantified as a bleaching halo on the surface of the apical, middle and coronal third. In the apical third, GPUI promoted greater NaOCl penetration (p < 0.05). GXP was better than GEC (p < 0.05), as was GPC (p > 0.05). The GPUI and GXP groups were similar in the middle and coronal third (p > 0.05). GPUI and GXP showed better results than GEC (p < 0.05). GPUI was more effective in the apical third and like GXP in the cervical and middle third.

Ultrasonic-Assisted Extraction of Antioxidants from Perilla frutescens Leaves Based on Tailor-Made Deep Eutectic Solvents: Optimization and Antioxidant Activity.

The development of natural antioxidants to replace synthetic compounds is attractive. Perilla frutescens leaves were proven to be rich in antioxidants. The extraction of antioxidants from Perilla leaves via ultrasonic-assisted extraction (UAE) based on choline chloride-based deep eutectic solvents (DESs) was studied. Firstly, several DESs were prepared, and their extraction effects were compared. Secondly, the extraction process was optimized by single-factor experiments and response surface methodology (RSM). Finally, the optimization results were verified and compared with the results of traditional solvent-based UAE. The effects of solvents on the surface cell morphology of Perilla frutescens leaves were characterized by scanning electron microscopy (SEM). Choline chloride-acetic acid-based DES (ChCl-AcA) extract showed a relatively high ferric-reducing antioxidant activity (FRAP) and 2,2-diphenyl-1-picrylhyldrazyl radical scavenging rate (DPPH). Under the optimal operating conditions (temperature 41 °C, liquid-solid ratio 33:1, ultrasonic time 30 min, water content 25%, ultrasonic power 219 W), the experimental results are as follows: DPPH64.40% and FRAP0.40 mM Fe(II)SE/g DW. The experimental and predicted results were highly consistent with a low error (<3.38%). The values of the DPPH and FRAP were significantly higher than that for the water, ethanol, and butanol-based UAE. SEM analysis confirmed that ChCl-AcA enhanced the destruction of the cell wall, so that more antioxidants were released. This study provides an eco-friendly technology for the efficient extraction of antioxidants from Perilla frutescens leaves. The cytotoxicity and biodegradability of the extract will be further verified in a future work.

Effect of transducer position on ultrasonic backscatter measurements of cancellous bone.

Ultrasonic backscatter techniques are being developed to detect changes in bone caused by osteoporosis and other diseases. Backscatter measurements performed at peripheral skeletal sites such as the heel may place the interrogated region of bone tissue in the acoustic near field of the transducer. The purpose of this study is to investigate how measurements in the near field affect backscatter parameters used for ultrasonic bone assessment. Ultrasonic measurements were performed in a water tank using a planar 2.25 MHz transducer. Signals were acquired for five transducer-specimen distances: N/4, N/2, 3 N/4, N, and 5 N/4, where N is the near-field distance, a location that represents the transition from the near field to far field. Five backscatter parameters previously identified as potentially useful for ultrasonic bone assessment purposes were measured: apparent integrated backscatter, frequency slope of apparent backscatter (FSAB), frequency intercept of apparent backscatter, normalized mean of the backscatter difference, and backscatter amplitude decay constant. All five parameters depended on transducer-specimen distance to varying degrees with FSAB exhibiting the greatest dependence on distance. These results suggest that laboratory studies of bone should evaluate the performance of backscatter parameters using transducer-specimen distances that may be encountered clinically including distances where the ultrasonically interrogated region is in the near field of the transducer.

Numerical investigation of cavitation in periodontal Pockets: Insights for enhancing cleaning efficiency.

Ultrasonic dental scalers are indispensable instruments for efficient dental cleaning through the generation of cavitation. To gain valuable insights and enhance the cavitation cleaning effects, a numerical investigation is conducted using the finite element method via ABAQUS. Numerical results are compared with the experimental cavitation image for a scaler undergoes vibrations near a wall. We then analyse how the amplitude, frequency, and cross-sectional shape of the scaler affect cavitation generation. Numerical results indicate that cavitation is more pronounced for a scaler oscillating near a nearly rigid boundary than a soft boundary. It increases with the vibration amplitude because of higher ultrasonic energy transferring to the liquid and generating stronger pressure waves. The resonant frequency of the scaler coincides with the maximum cavitation and scaler tip amplitude. Reducing the dimension of the cross-section of the scaler in its oscillation direction increases both the scaler tip amplitude and the cavitation generated. This finding offers a potential design approach for enhancing the scaler cavitation and its cleaning effects. These insights provide practical guidance for optimising dental scaler settings, which can improve oral hygiene and prevent complications related to dental implants.

Predictive Mouse Ultrasonic Vocalization Sequences: Uncovering Behavioral Significance, Auditory Cortex Neuronal Preferences, and Social-Experience-Driven Plasticity.

Mouse ultrasonic vocalizations (USVs) contain predictable sequential structures like bird songs and speech. Neural representation of USVs in the mouse primary auditory cortex (Au1) and its plasticity with experience has been largely studied with single-syllables or dyads, without using the predictability in USV sequences. Studies using playback of USV sequences have used randomly selected sequences from numerous possibilities. The current study uses mutual information to obtain context-specific natural sequences (NSeqs) of USV syllables capturing the observed predictability in male USVs in different contexts of social interaction with females. Behavioral and physiological significance of NSeqs over random sequences (RSeqs) lacking predictability were examined. Female mice, never having the social experience of being exposed to males, showed higher selectivity for NSeqs behaviorally and at cellular levels probed by expression of immediate early gene c-fos in Au1. The Au1 supragranular single units also showed higher selectivity to NSeqs over RSeqs. Social-experience-driven plasticity in encoding NSeqs and RSeqs in adult females was probed by examining neural selectivities to the same sequences before and after the above social experience. Single units showed enhanced selectivity for NSeqs over RSeqs after the social experience. Further, using two-photon Ca2+ imaging, we observed social experience-dependent changes in the selectivity of sequences of excitatory and somatostatin-positive inhibitory neurons but not parvalbumin-positive inhibitory neurons of Au1. Using optogenetics, somatostatin-positive neurons were identified as a possible mediator of the observed social-experience-driven plasticity. Our study uncovers the importance of predictive sequences and introduces mouse USVs as a promising model to study context-dependent speech like communications.SIGNIFICANCE STATEMENT Humans need to detect patterns in the sensory world. For instance, speech is meaningful sequences of acoustic tokens easily differentiated from random ordered tokens. The structure derives from the predictability of the tokens. Similarly, mouse vocalization sequences have predictability and undergo context-dependent modulation. Our work investigated whether mice differentiate such informative predictable sequences (NSeqs) of communicative significance from RSeqs at the behavioral, molecular, and neuronal levels. Following a social experience in which NSeqs occur as a crucial component, mouse auditory cortical neurons become more sensitive to differences between NSeqs and RSeqs, although preference for individual tokens is unchanged. Thus, speech-like communication and its dysfunction may be studied in circuit, cellular, and molecular levels in mice.

Behavioral analysis in laboratory rats: Challenges and usefulness of 50-kHz ultrasonic vocalizations.

Many rodent species emit and detect vocalizations in the ultrasonic range. Rats use three classes of ultrasonic vocalizations depending on developmental stage, experience and the behavioral situation. Calls from one class emitted by juvenile and adult rats, the so-called 50-kHz calls, are typical for appetitive and social situations. This review provides a brief historical account on the introduction of 50-kHz calls in behavioral research followed by a survey of their scientific applications focusing on the last five years, where 50-kHz publications reached a climax. Then, specific methodological challenges will be addressed, like how to measure and report 50-kHz USV, the problem of assignment of acoustic signals to a specific sender in a social situation, and individual variability in call propensity. Finally, the intricacy of interpreting 50-kHz results will be discussed focusing on the most prevalent ones, namely as communicative signals and/or readouts of the sender's emotional status.

State of the art on microbubble cavitation monitoring and feedback control for blood-brain-barrier opening using focused ultrasound.

Focused ultrasound (FUS) is a non-invasive and highly promising method for targeted and reversible blood-brain barrier permeabilization. Numerous preclinical studies aim to optimize the localized delivery of drugs using this method in rodents and non-human primates. Several clinical trials have been initiated to treat various brain diseases in humans using simultaneous BBB permeabilization and drug injection. This review presents the state of the art ofin vitroandin vivocavitation control algorithms for BBB permeabilization using microbubbles (MB) and FUS. Firstly, we describe the different cavitation states, their physical significance in terms of MB behavior and their translation into the spectral composition of the backscattered signal. Next, we report the different indexes calculated and used during the ultrasonic monitoring of cavitation. Finally, the differentin vitroandin vivocavitation control strategies described in the literature are presented and compared.

Response Surface Methodology-Based Optimized Ultrasonic-Assisted Extraction and Characterization of Selected High-Value Components from Gemlik Olive Fruit.

This article presents an optimized ultrasound-assisted ethanolic extraction (UAEE) and characterization of selected high-value components from Gemlik olive fruit (GOF) harvested from Potohar region of Pakistan. Response surface methodology (RSM), involving central composite design (CCD), was applied to optimize the extraction variables i. e., temperature (25-65 °C), extraction time (15-45 min) and aqueous ethanol concentration (60-90 %) for optimal recovery of bioactives extract, total phenolic contents (TPC) and DPPH free radical scavengers. Under the optimized set of conditions such as 43 °C temperature, 32 min extraction time and 80 % aqueous ethanol, the best extract yield (218.82 mg/g), TPC (19.87 mg GAE/g) and DPPH scavenging activity (63.04 %) were recorded. A quadratic polynomial model was found to be reasonably fitted to the observed results for extract yield (p<0.0001 and R2 =0.9941), TPC (p<0.0001 and R2 =0.9891), and DPPH radical scavenging activity (p<0.0001 and R2 =0.9692). Potent phenolic compounds were identified by GC/MS in GOF extract and considerable amount of essential fatty acids were also detected. The current findings support the use of UAEE as an effective green route for optimized recovery of high-value components from GOF and hence its applications can be extended to functional food and nutra-pharmaceutical developments.

Ultrasonic-assisted extraction of flavonoids from Nitraria sibirica leaf using response surface methodology and their anti-proliferative activity on 3T3-L1 preadipocytes and antioxidant activities.

As both an edible and medicinal plant, Nitraria sibirica has been used as a natural remedy for indigestion and hypertension since ancient times in Central Asia. The ethanolic extract of N. sibirica leaves lowers blood pressure and blood lipids. We assume that these bioactivities are most likely related to the composition of flavonoids due to their dominant content. Therefore, we investigated bioactivity-oriented extraction parameters of flavonoids from N. sibirica. In this study, the ultrasonic-assisted extraction variables were optimized using a response surface methodology for optimal recoveries of total flavonoid content (TFC), anti-proliferative activity on 3T3-L1 preadipocytes and antioxidant capacities (DPPH) of N. sibirica leaf extract (NLE). The optimal extraction conditions of NLEs were as follows: ethanol concentration of 71.33%, feed-to-solvent ratio of 30.36 mL/g, extraction temperature of 69.48°C, extraction time of 25.27 min, extraction number of two times, the TFCs were 1.73 ± 0.01 mg RE/g d.w. (n = 4), IC50 value of preadipocytes was 259.42 ± 3.62 µg/mL (n = 4), and antioxidant capacity of 86.55 ± 3.71% (n = 4). After the purification of NLEs, the TFCs were 7.52 mg RE/g d.w., the inhibition capacity of IC50 was 143.50 µg/mL, and DPPH scavenging rate was 86.99%, which were approximately 4.34, 1.81, and 1.01 folds higher than before the purification of NLEs, respectively. Bioactive-oriented extraction of NLEs possessed the potential lipid lowering and antioxidant activities, which hold high research value for the development of natural medicines or new functional foods to treat or prevent metabolic diseases such as obesity.

A comparison of ultrasonic, ozone, and enzyme pre-treatments on cheese whey degradation for enhancement of anaerobic digestion.

Lactose in cheese whey wastewater (CWW) makes it difficult to degrade under normal conditions. The effect of ultra-sonication (US), ozonation and enzymatic hydrolysis on increasing the bioavailability of organic matter in CWW and biogas production were evaluated. The pre-treatment conditions were: specific energy input varied from 2130 to 8773KJ/KgTS for a sonication time of 4.5-18.5 min, Ozone (O3) dosages ranging from 0.03 to 0.045gO3/gTS were applied for 4-16 min, pH (3.8-7.1), temperature (35°C-55°C), enzyme dosage (0.18-0.52%), was operated from 7.75 to 53 min for enzymatic hydrolysis by ß-galactosidase. The results of the US reported a maximum sCOD solubilisation of 77.15% after 18.5 min of operation, while the corresponding values for ozonation and enzymatic methods were 64.8% at 16 min and 54.79%, respectively. The organic matter degradation rates evaluated in terms of protein and lactose hydrolysis were 68.78%,46.03%; 47.83%,16.15% and 54.22%,86.2%respectively, for US, ozonation and enzymatic methods. The cumulative methane yield for sonicated, ozonised and enzymatically hydrolysed samples were 412.4 ml/g VS, 361.2 ml/g VS and 432.3mlCH4/gVS, respectively. Regardless of the lower COD solubilisation rates attained, enzymatic pre-treatment showed maximum methane generation compared to US and ozonation. This could be attributable to the increased activity of ß-galactosidase in hydrolysing whey lactose. The energy calculations revealed that the pre-conditioning of organic-rich CWW with enzymatic hydrolysis is more effective and efficient, yielding a net energy gain (gross output energy-input energy) of 9166.7 KJ and an energy factor (ratio of output to input energy) of 6.67. The modified Gompertz model well simulated all experimental values.

A Conformable Ultrasound Patch for Cavitation-Enhanced Transdermal Cosmeceutical Delivery.

Increased consumer interest in healthy-looking skin demands a safe and effective method to increase transdermal absorption of innovative therapeutic cosmeceuticals. However, permeation of small-molecule drugs is limited by the innate barrier function of the stratum corneum. Here, a conformable ultrasound patch (cUSP) that enhances transdermal transport of niacinamide by inducing intermediate-frequency sonophoresis in the fluid coupling medium between the patch and the skin is reported. The cUSP consists of piezoelectric transducers embedded in a soft elastomer to create localized cavitation pockets (0.8 cm2 , 1 mm deep) over larger areas of conformal contact (20 cm2 ). Multiphysics simulation models, acoustic spectrum analysis, and high-speed videography are used to characterize transducer deflection, acoustic pressure fields, and resulting cavitation bubble dynamics in the coupling medium. The final system demonstrates a 26.2-fold enhancement in niacinamide transport in a porcine model in vitro with a 10 min ultrasound application, demonstrating the suitability of the device for short-exposure, large-area application of sonophoresis for patients and consumers suffering from skin conditions and premature skin aging.

Barrier-breaking effects of ultrasonic cavitation for drug delivery and biomarker release.

Recently, emerging evidence has demonstrated that cavitation actually creates important bidirectional channels on biological barriers for both intratumoral drug delivery and extratumoral biomarker release. To promote the barrier-breaking effects of cavitation for both therapy and diagnosis, we first reviewed recent technical advances of ultrasound and its contrast agents (microbubbles, nanodroplets, and gas-stabilizing nanoparticles) and then reported the newly-revealed cavitation physical details. In particular, we summarized five types of cellular responses of cavitation in breaking the plasma membrane (membrane retraction, sonoporation, endocytosis/exocytosis, blebbing and apoptosis) and compared the vascular cavitation effects of three different types of ultrasound contrast agents in breaking the blood-tumor barrier and tumor microenvironment. Moreover, we highlighted the current achievements of the barrier-breaking effects of cavitation in mediating drug delivery and biomarker release. We emphasized that the precise induction of a specific cavitation effect for barrier-breaking was still challenged by the complex combination of multiple acoustic and non-acoustic cavitation parameters. Therefore, we provided the cutting-edge in-situ cavitation imaging and feedback control methods and suggested the development of an international cavitation quantification standard for the clinical guidance of cavitation-mediated barrier-breaking effects.

Antimicrobial effectiveness of ultrasonic irrigation in root canal treatment: a systematic review of randomized clinical trials and meta-analysis.

OBJECTIVE: The objective of this systematic review and meta-analysis (SRM) was to answer the question as to whether the use of ultrasonic irrigation (UI) results in better antimicrobial activity in root canal disinfection compared to conventional irrigation (CI). METHODS: A literature search was performed in the main scientific databases, carried out until October 2021. The eligibility criteria were randomized clinical trials (RCTs). Two meta-analyses were conducted using R software with the "META" package. The mean difference (MD) and odds ratio (OR) measure of effect were calculated. The fixed effect model was applied with a 95% confidence interval. The Cochrane collaboration scale was used to assess risk of bias and the GRADE tool to assess the quality of evidence. RESULTS: A total of 1782 records were screened, and 12 studies meeting the criteria were included in this review. A low risk of bias was observed for most domains, except allocation concealment that was considered unclear. The certainty of evidence was classified as moderate in the OR meta-analyses and low in the MD meta-analyses. Ultrasonic irrigation resulted in a better antimicrobial effect in both meta-analyses, MD 1.42 [1.60; 1.23] p < 0.0001, I2 = 80%; and OR 3.86 [1.98; 7.53] p< 0.0001, I2 = 28.7%. CONCLUSION: Within the limitations of this SRM, UI presented better antimicrobial efficacy than CI. CLINICAL RELEVANCE: UI should be used by clinicians as it promotes better antimicrobial efficacy in patients undergoing endodontic treatment.

Synchrotron X-ray imaging of the onset of ultrasonic horn cavitation.

High-power ultrasonic horns operating at low frequency are known to generate a cone-shaped cavitation bubble cloud beneath them. The exact physical processes resulting in the conical structure are still unclear mainly due to challenges associated with their visualization. Herein, we address the onset of the cavitation cloud by exploiting high-speed X-ray phase contrast imaging. It reveals that the cone formation is not immediate but results from a three-step phenomenology: (i) inception and oscillation of single bubbles, (ii) individual cloud formation under splitting or lens effects, and (iii) cloud merging leading to the formation of a bubble layer and, eventually, to the cone structure due to the radial pressure gradient on the horn tip.

Evaluating the effects of nanoparticles combined ultrasonic-microwave thawing on water holding capacity, oxidation, and protein conformation in jumbo squid (Dosidicus gigas) mantles.

Magnetic nanoparticles (MNPs) have a dual role in acting as magnetic and sonosensitizer agents, which can combine the synergistic effects of microwave and ultrasonic waves. To study the effects of MNPs combined ultrasonic-microwave thawing (NUMT) on the water holding capacity (WHC), oxidation of protein and lipid, and protein conformation, jumbo squid mantles were subjected to cold storage thawing (CST), MNPs combined ultrasonic thawing (NUT), MNPs combined microwave thawing (NMT) and NUMT. Results showed that NUMT treatment had a higher WHC, lower oxidation, effectively reduced myofibrillar protein aggregation and degradation, and stabilized the structure of the protein of the jumbo squid. The muscle fiber structure of NUMT treated jumbo squid mantles was dense, orderly with a smooth surface, and the fiber network gaps were small and uniformly distributed. This study shows that NUMT can ameliorate the thawing qualities of jumbo squid, and is an effectively thawing method.

Portable Microwave-Acoustic Coaxial Thermoacoustic Probe With Miniaturized Vivaldi Antennas for Breast Tumor Screening.

Microwave-induced thermoacoustic (TA) imaging (MTAI), which exploits dielectric contrasts to provide images with high contrast and spatial resolution, holds the potential to serve as an additional means of clinical diagnosis and treatment. However, conventional MTAI usually uses large and heavy metal antennas to radiate pulsed microwaves, making it challenging to image different target areas flexibly. In this work, we presented the design and evaluation of a portable microwave-acoustic coaxial TA probe (51 mm × 63 mm × 138 mm) that can flexibly image the region of interest. The TA probe contains two miniaturized symmetrically distributed Vivaldi antennas (7.5 g) and a 128-element linear ultrasonic transducer. By adjusting the geometry of the antennas and the ultrasonic transducer, the TA probe's acoustic field and microwave field can be designed to be coaxial, which helps achieve homogeneous microwave illumination and high-sensitivity ultrasonic detection. The practical feasibility of the proposed probe was tested on an in vitro ewe breast and a healthy volunteer. The results demonstrate that the MTAI system with the proposed TA probe can visualize the anatomical structure of the breast tumor in ewe breast and a healthy volunteer breast with resolutions in hundreds of microns (transverse: 910 µm, axial: 780 µm) and an excellent signal-to-noise ratio can be obtained in deep adipose tissue (10 dB in 6 cm fat). The miniaturized portable TA probe takes a solid step forward in translating MTAI technology to clinical breast tumor diagnosis.

Process Optimization of Phytoantioxidant and Photoprotective Compounds from Carob Pods (Ceratonia siliqua L.) Using Ultrasonic Assisted Extraction Method.

The current study first describes the extraction of phytoantioxidant polyphenols from Carob byproducts (pods) using maceration and heating-assisted extraction as traditional methods and ultrasonic-assisted extraction (UAE) as an innovative method to determine the most efficient extraction process in terms of four targeted responses: total phenolic content (TPC), antioxidant activities (TAC and DPPH), and photoprotective properties as measured by the sun protection factor (SPF). Second, we used response surface methodology (RSM) with a central composite rotatable design (CCDR) approach to investigate the influence of process variables (extraction time, extraction temperature, and solvent concentration) on UAE, which was found to be the most effective extraction technique in our study. Carob byproduct extracts had a TPC ranging from 6.21 to 21.92 mg GAE/g dw, a TAC ranging from 22.00 to 49.30 mg AAE/g dw, DPPH scavenging activity ranging from 56.35 to 90.50%, and SPF values ranging from 8.62 to 22.37. The optimal UAE conditions for maximum TPC, TAC, DPPH, and SPF responses were determined to be 38.90% ethanol, 53.90 °C, and 50.92 min. Using Carob as a source for sustainable and bioactive products in conjunction with optimized UAE is a promising contribution to the cosmetic industry that will help to strengthen the concept of environmentally-friendly "green chemistry". Given that Carob pulp or seeds are considered food byproducts, the research presented here encourages the use of these agri-food waste materials in cosmetics.

Frequency dependence of the ultrasonic power reflected from the water-tissue interface of human cancellous bone in vitro.

Numerous studies have performed in vitro ultrasonic measurements of cancellous bone in water to develop techniques for ultrasonic bone assessment. Because cancellous bone is a highly porous medium, ultrasonic reflections at the water-bone interface may be frequency dependent. The goal of this study was to investigate the effect of porosity on the frequency dependence of the reflected power. Ultrasonic measurements were performed in a water tank at room temperature on 15 specimens of cancellous bone prepared from the proximal end of 9 human femurs using single element, broadband transducers with center frequencies of 3.5, 5, 7.5, and 10 MHz. Power spectra of pulses reflected from the water-specimen interface were corrected for the frequency response of the measurement system to obtain the reflected power in decibels RdB(f). To suppress random phase cancellation effects, RdB(f) was averaged over multiple sites on multiple specimens. A frequency dependence of RdB(f) was observed in the 2.6-10 MHz range. The frequency dependence was moderate, with a maximum change of less than 6 dB over the entire frequency range. RdB(f) was greatest for low porosity specimens. The frequency averaged intensity reflection coefficient ranged from 7.4 × 10-4 to 7.8 × 10-3 for high and low porosity specimen groups, respectively.

Cavitation in a periodontal pocket by an ultrasonic dental scaler: A numerical investigation.

Periodontal pockets are spaces or holes surrounded by teeth under the gum line. These pockets can become filled with infection-causing bacteria resulting in tissue, bone, and tooth loss. Cavitation produced by the oscillating tip of dental ultrasonic scalers plays a significant role in routine periodontal therapy to clean these areas. Numerical studies were conducted for a scaler vibrating in a periodontal pocket which was simplified to a hole, using ABAQUS based on the finite element method. The simulations consider the three-dimensional, nonlinear, and transient interaction between the vibration and deformation of the scaler tip, the water flow around the scaler and the cavitation formation. The numerical model was validated by comparing results with experimental data for a scaler vibrating in an unbounded liquid, the displacement at the free end of the scaler and the cavitation pattern near the scaler tip displaying excellent agreement. A parametric study for a scaler vibrating in a hole has been carried out in terms of the volume of the hole, the taper ratio (the radius ratio between the circular opening and bottom of the hole), and the immersion depth of the scaler tip in the hole. The amount of cavitation generated is evaluated by the cavitation density (or the void fraction) which is the ratio of the volume of the cavitation occupied in the hole to the total volume of the hole. Numerical results indicate that the cavitation density in the hole increases with the decreasing hole volume and the increasing taper ratio. It is inferred that cleaning effects could be increased if some modifications to the scaler design could be made to increase the blocking effect of the hole during the cleaning process. Cavitation is observed in the hole even if the scaler is placed above the hole and increases with the immersion depth.

Developing high intensity ultrasonic cleaning (HIUC) for post-processing additively manufactured metal components.

The high energy phenomenon of cavitation bubble collapses has enabled numerous applications, including cleaning. In ultrasonic cleaning, cavitation intensity is typically lower than in other applications, such as sonochemistry and material processing. However, there has been an emerging application in intense cleaning of metal additively manufactured (AM) components. The presence of partially melted powders on AM surfaces is undesirable, contributing to high surface roughness and posing contamination risks during usage. We designed a high-intensity cavitation cleaning process that has significantly higher inertial cavitation intensity - i.e., erosion potential - than a conventional ultrasonic cleaning tank. Through acoustic signal characterisation, we showed that placing transducer sets on four sides of the tank could effectively focus and generate high-amplitude pressure waves directed towards the central region. Strong subharmonic signals indicate intensely inertial cavitation throughout the tank. Cavitation intensities were measured at various locations to understand the wave transmission characteristics and distribution patterns. Our results show that the cavitation intensity distribution is highly dependent on the height position. Finally, we demonstrated that the high intensity ultrasonic cleaning (HIUC) process could remove partially melted powders from an AM surface - which was not possible through conventional ultrasonic cleaning. HIUC could lead to higher cleaning efficiency and enhanced AM specimen cleanliness.